Page Content

ORS demonstration in four steps

Step 1: ensure that RJ45 provides Internet
Step 2: prepare ORS
Step 3: run demo
Step 4: packing up after demonstration

Step 1: ensure that RJ45 provides Internet

You will need:

LAN cable
RJ45 USB adapter
Wifi Ethernet extender
A laptop

Step 1.1 Setting your smartphone as Wifi access point

First you need to set your smartphone as a Wifi access point.
Ssid: Nexedi
Password: 0120034005
Connect by Wifi your laptop to your smartphone access point.
Try Internet access by connecting to www.google.com
If OK, move to next step (1.2), if not find reason why you cannot connect to the Internet via your smartphone.

Step 1.2 Testing the LAN cable

Then you need to test that the LAN cable provides Internet access.
For this, turn off Wifi on your laptop.
Then plug the USB RJ45 adapter to your laptop. The USB RJ45 LAN cable should be also connected to the Wifi Ethernet adapter.
Try Internet access by connecting to www.google.com
If OK, move to next step (1.3)
If not find reason why you can't connect to Internet via your USB RJ45 adapter and LAN cable

Step 1.3 Turning on Wifi on laptop

Disconnect USB RJ45 adapter from your laptop.
Disconnect LAN cable from USBRJ45 adapter.
Turn on Wifi on your laptop
You no longer need USB Ethernet adapter. You can put it away.
Move to step 2.

Step 2: prepare ORS

For this step, you need:

ORS (with antenna already set)
ORS power adapter
POE cable
LAN cable
Wifi ethernet gateway

WARNING: Connect everything exactly and in the same order as in the pictures, otherwise devices might break or the demonstration might not work.

Step 2.1.1: Connecting the POE cable

Connect POE cable to POE connector of ORS power adapter

Step 2.1.2: Connecting the LAN cable

Connect LAN cable to LAN connector of ORS power adapter

Step 2.2 Plugging ORS power adapter to power

Plug ORS power adapter to power
You should hear "bip". If not, find reason.
After "bip", wait 10 minutes
Move to step 2.3

Step 2.3 Checking the panel rapid.space 1/3

Go to panel Rapid.Space
Go to "servers"
Make sure ORS125 is green
Move to step 2.4

Step 2.4 Checking the panel rapid.space 2/3

Go to panel Rapid.Space
Go to "services"
Make sure all services are green (except eNodeB which can be grey and GnodeB which can be red sometimes
Move to step 2.5

Step 2.5 Checking the panel rapid.space 3/3

If everything is green or grey at 2.4, turn on phones for demo ( Step 3)
If not...Go to panel rapid.space
Click on "Access Monitor"
This will open a new tab/window
Click on "Synchronise" to update the display of monitoring.
It is normal that check-rx-saturated" is red if ORS uses same frequency as operator.
It is normal that some promises are red for a few minutes if ORS reconfigures
In all other cases, ask support

Step 3 Run the demonstration

Turn on phones
Make sure 5G appears
Make messaging demo
Make video demo

Step 3.1 Switch off

To turn off ORS, disconnect AC before anything else

Step 4: Packing up 1/3

Here is how to pack everything so that nothing gets damaged when travelling
Put the ORS, the ORS mounting kit (you might not have this, not necessary for the demo), the two antennas and the two N-to-SMA adaptors in the box as such
Add plastic wrapping so nothing moves during your journey
Add the Wifi gateway
Add plastic wrap
Finally, put the styrofoam cover and close the box.

Step 4.1: Packing up 2/3

Wrap the POE power supply like this

Step 4.2: Packing up 3/3

Put the ORS box in the big cardboard box, wrap the two phones in plastic bags, and put the two phones, the POE power supply box, the POE 5m Ethernet cable, the LAN cable, the RJ45 adaptor (optional) and the power strip (optional) in the box as shown above.